#2003-P and #2003-PSC (Restoration Coatings)
DESCRIPTION
SEALMARK # 2003-P and #2003-PSC Restoration Coatings are blend of water based acrylic resins, select fillers, ceramic particles, and a unique mixture of algaecides and biocides. The only difference between the # 2003-P and the #2003-PCS coatings is the size of the ceramic particles. The #2003-PSC Satin Coating incorporates the use of very fine micro sized ceramic particles the form a semi gloss, enamel smooth, coating film. You must use the #2000-SP primer with the #2003-PSC Satin Coating to achieve the enamel smooth finish coat. The #2003-P Restoration Coating is formulated with larger size ceramic particles and yields a semi smooth flat paint film. Either the #2000 or the #2000-SP primers can be used in conjunction with the #2003-P Restoration Coating. The #2003 series coatings are a high solids (60%) heavy bodied, flexible coatings available in a rainbow of colors formulated to waterproof and protect a variety of substrates exposed to all weather conditions. A 20 year material warranty is available for the #2003 series coatings.
USES
The Sealmark #2003 series coatings can be applied to a variety of exterior substrates to provide maximum protection from severe weather conditions. These flexible, hydrophobic coatings can be applied to wood, metal, aluminum, existing or new eifs, stucco, or masonry, cured concrete, aged vinyl siding or previously painted stable substrates. The #2003 series coatings will fill, bridge and hide hairline cracks and waterproof stucco and masonry substrates. The unique formulation of the #2003 series coatings has a tenacious bond to all properly prepared substrate surfaces and is extremely resistant to UV degradation, chipping, peeling. cracking and surface delamination.
COVERAGE
The recommended coverage rate for the Sealmark #2003 series coatings are 270 sq ft per gallon. This coverage rate will yield approximately a 6mil wet film thickness. 2 coats at the above coverage rate are required to maximize longevity and ensure waterproofing properties, sustain crack bridging and qualify for the product warranty. When applying to unsealed or unprimed porous substrates, coverage rates will decrease.
PROPERTIES
DRYING TIME- After the application of the Sealmark #2003 series coatings, the drying time is dependent on the ambient air temperature and relative humidity (RH). Under normal conditions (70°F and 55% RH) the time elapsed for acceptable curing is a minimum of 4 hours before application of the second coat. After 24 hour period the #2003 coating is in a complete cured form. NOTE: High relative humidity, damp conditions, and cool temperatures will require longer drying times.
WATER VAPOR TRANSMISSION- ASTM E-96 average perm rating 1.57
APPLICATION PROCEDURES
Job Conditions- Temporary protection shall be provided at all times for a specified duration until the
# 2003 coating has achieved a completely cured state to protect from all weather, nature, elements, and other potential damage.
Surface Preparation- Surface must be clean, dry, structurally stable and surface temperature should be above 40°F. Surface area should be free from grease, oils, solvents, and silicone based products that can possibly interfere with bond integrity. When applying system materials to concrete, brick, or masonry wall: these substrates must age a period of 30 days and the surface PH must not exceed a PH of 9. To lower the PH of these substrates, wash with a mild solution of muratic acid and clean water. Thoroughly wash solution from substrate with clean water and allow it to dry before proceeding with coating application. When filling small surface cracks, Sealmark #1001 Brush Grade caulk can be knifed into crack to level with surrounding surface. For larger cracks 1/8" or larger use Sealmark #2010 Surface leveler to fill crack level with surface. Before proceeding with coating application allow the crack repair products to dry. Unpainted substrates must be primed with one of the Sealmark #2000 series primers. Remember that Sealmark cannot be applied to any asphalt or polyethylene plastic materials.
Mixing Procedures- Proper mixing procedure for Sealmark #2003 is to mix gently in pail for 60 seconds with a low RPM drill and standard paint mixing bit.
Application- No special tools or skills are needed for the correct application of the Sealmark #2003 coatings. Using a heavy duty paint roller/ applicator, apply Sealmark #2003 in a uniform consistent manner as to completely cover the prepared substrate. Other approved tools for the application of Sealmark # 2003 include a good quality brush or an appreciate airless sprayer with 2,800 p.s.i. and a minimum tip size of 26/1000th . DO NOT BACK-ROLL or BRUSH OVER AN AREA ONCE RESTORATION COATING HAS BEEN APPLIED UNTIL DRY. (This will interrupt the uniformity and coverage of the #2003).
Clean Up- Use soap and water for clean up. System materials are water-borne and are non-toxic. Prior to curing, system materials are water soluble. Clean up any spills, overspray, or residue of the system materials before they have time to set. Cured or dried system materials are not water soluble and may prove to be difficult to impossible to remove without damage to substrate or other materials upon which they have dried. Dispose of waste materials and empty containers into an approved waste disposal facility. Never dump materials into storm or sanitary sewers, nor into bodies of water.
STORAGE
Sealmark #2003 Coating must be stored in a continuous environmental temperature of at least 45°F or higher Storing in temperatures closer to normal room temperature 70°F will result in easier application. ALWAYS AVOID FREEZING. Always store in tightly sealed container and away from direct sunlight. Shelf life of Sealmark # 2003 coatings is for a period of 1 year after products are manufactured.
CAUTIONS
As with any type of application, take the appropriate steps necessary to ensure that clean up of #2003 is achieved with minimal effort. This means properly tarp/secure application area as to prevent unintended application as product may prove to be difficult to remove. SOME WALL SUBSTRATES MAY HAVE BEEN COATED WITH ACLEAR SILICON WATER REPELLENT THAT WOULD ADVERSELY AFFECT THE ADHESION OF SEALMARK PRODUCTS. IF APPLICATION OF THE SILICON TREATMENT IS UNKNOWN; IT IS RECOMMENDED THAT A TEST APPLICATION BE APPLIED TO THE SUBSTRATE AND CHECKED AFTER CURING FOR ADHESION.
(TECHNICAL AND JOB SITE ASSISTANCE AVAILABLE UPON REQUEST)
Click here to download the Material Safety Data Sheet (MSDS) for this product.
